TPE material or rubber: Thermoplastic elastomers and rubber in direct comparison
TPE (thermoplastic elastomers) and rubber are elastic materials for Seals, However, profiles and grip zones differ fundamentally in structure, processing, temperature resistance and recyclability. Rubber is chemically bonded and non-fusible. TPE is physically bonded and can be melted and injection molded like a plastic. This comparison illustrates EPDM, It compares the most commonly used rubber to the common TPE types and discusses the advantages and disadvantages, temperature limits, processing, recycling, and price development.
1. TPE or rubber: Which is better?
Whether TPE or rubber is more suitable depends on the requirements profile of the component. Rubber types such as EPDM are particularly suitable for high continuous temperatures and permanent compression, while TPE is well suited for high volumes, 2K bonding with plastic and recycling requirements. The appropriate material is selected based on the operating temperature, the required mechanical durability, media contact, volume requirements, and sustainability goals.
What is the biggest difference between rubber and TPE?
The fundamental difference between rubber and TPE lies in the crosslinking. Rubber is vulcanised Rubber, A thermoplastic elastomer combines a soft, elastic phase with a hard, thermoplastic phase. In TPE, the crosslinking is purely physical: at room temperature, the material behaves like rubber, and when heated it becomes malleable and can be processed like plastic. Depending on the chemical base, TPE-S (styrol block copolymers, e.g. SEBS), TPE-V (crosslinked EPDM in polypropylene), TPE-O (thermoplastic elastomer with a high molecular weight), TPE-P (thermoplastic elastomer with a low molecular weight), TPE-Q (thermoplastic elastomer with a high molecular weight) and TPE-R (thermoplastic elastomer with a low molecular weight) are distinguished., TPE-U and TPE-E.
Which type of rubber can be used as an alternative to TPE?
When rubber is considered as an alternative to TPE, EPDM (ethylene propylene diene rubber) is usually used. EPDM is used for seals and profiles in outdoor applications, in automotive and construction technology, and in contact with water and steam, that is, where TPE is also often used. Occasionally, TPE also replaces natural rubber (NR) or styrene-butadiene rubber (SBR), for example in grips, buffers, or mats. The most important comparison in practice is therefore between EPDM and the TPE types TPE-V and TPE-S.
Not every rubber-based polymer can be effectively replaced with TPE. Fluoroplastic (FKM) and silicone (VMQ) are designed for continuous temperatures above 200 °C, while FKM and HNBR are also suitable for contact with oils, fuels, and aggressive chemicals. NBR is the standard for oil-resistant seals. TPE does not achieve this temperature and media resistance, which is why rubber remains the technically correct choice for these applications.
2. What are the advantages and disadvantages of TPE compared to rubber?
The main advantages of TPE over rubber are faster and cheaper injection molding processing, easy combination with rigid plastics, recyclability, easy coloring, and lower material cost. The disadvantages include lower temperature resistance, higher residual compressive deformation under continuous load, limited oil resistance, and higher tooling costs.
Advantages of TPE over rubber:
- Economic processing: TPE is like a thermoplastic injection molded or extruded. The vulcanization process is eliminated and the cycle times are significantly shorter.
- Multi-component components: TPE can be directly combined with hard plastics such as PP, PA or ABS in 2K injection molding.
- Recyclability: The splinters and chips can be melted again and the components are recyclable.
- Freedom of design: TPE can be colored with pigments in almost any color, and it is also possible to make it transparent or translucent.
- Lower weight: Many TPE types have a lower density than filled rubber compounds.
- Welding ability: TPE profiles can be thermally welded, for example for frame seals.
- Material price: TPE produced in Germany costs about 5 to 13 EUR/kg in 2026, which is on average lower than EPDM blends at about 6 to 15 EUR/kg.
Disadvantages of TPE compared to rubber:
- Limited temperature resistance: Above the softening temperature of the hard phase, TPE loses its form stability.
- Higher pressure deformation residual: TPE has a lower return ability when deformed over time, especially at elevated temperatures, compared to vulcanized rubber.
- Crawling and tension relaxation: Under static continuous load, the restoring force of TPE decreases more quickly than that of rubber.
- Reduced media stability: Many TPE types, especially TPE-S, are prone to leaking in oils and fats.
- Higher tool costs: Injection molding tools are more expensive than press tools for rubber. TPE is therefore economical primarily for larger quantities.
3. Which material is more resistant to temperature changes: EPDM or TPE?
Generally, EPDM is more temperature-resistant than TPE. EPDM can be used permanently at temperatures up to about +130 °C and exhibits very low residual compressive deformation in this range. EPDM can also be used at higher temperatures for a short period of time. Peroxide-crosslinked EPDM types can be temperature-stable up to 150 °C and are also highly resistant to hot water and steam.
The maximum service temperature of TPE depends on the type: TPE-S reaches about +80 °C depending on the formulation, while TPE-V reaches about +130 °C. With the maximum service temperature, TPE is therefore roughly on the same level as EPDM. The relevant difference between EPDM and TPE lies in the residual compressive deformation. Since TPE softens at heat, the residual compressive deformation increases significantly with increasing temperature. A TPE seal can remain mechanically intact at 100 °C, but loses its sealing strength more quickly than a comparable EPDM seal.
In the low-temperature range, EPDM remains flexible up to approximately −50 °C, TPE-V typically up to approximately −40 °C. All temperature specifications mentioned for EPDM and TPE are guidelines, as the exact properties depend on the additives in the raw material mixture.
4. EPDM vs. TPE: Comparison for industrial seals
Industrial seals that are permanently pressed and exposed to higher temperatures are usually made from EPDM due to their better mechanical properties. TPE material, on the other hand, is used for industrial seals that are installed in high quantities at moderate temperatures.
- EPDM is particularly suitable for static seals under continuous pressure, especially for hot water and steam applications, as well as for small to medium-sized quantities and large cross sections.
- TPE is suitable for seals that are injection molded directly into plastic housings, for large series with moderate temperature loads, and for special recycling requirements.
EPDM and TPE are equally resistant to weathering, ozone and UV radiation and have corresponding approvals (e.g. FDA, Available for contact with food or drinking water according to KTW-BWGL, DVGW W 270. Unlike mineral oils and fuels, neither EPDM nor standard TPE is suitable.
5. The properties of EPDM and TPE compared
When choosing between EPDM and TPE, three questions are particularly relevant: what is the maximum operating temperature, how strongly is the component permanently pressed and in what quantity is it manufactured? At high temperatures and with permanent pressing, EPDM is recommended. For large series, plastic composites and recycling requirements, TPE is more suitable. All figures are typical values and may vary depending on the compound.
| Property | EPDM | TPE (TPE-V / TPE-S) |
| Networking | chemically (vulcanization), not fusible | physically, fusible |
| Durable use temperature | approx. −50 to +130 °C | TPE-S: approx. −40 to +80 °C TPE-V: approx. −40 to +130 °C |
| Residual compressive deformation under heat | low (very good) | high, increases with the temperature |
| Weather, ozone, UV | very good | Good to very good |
| Hot water and steam | very good (peroxide-like) | limited |
| Oil and fuel resistance | slight | low to moderate |
| Processing | Presses, injection molding, extrusion with vulcanization | Injection molding and extrusion like thermoplastics |
| Cycle time | Minutes | Seconds |
| 2K compound with plastic | possible with a holding device system, but is time-consuming | Easily possible by over-spraying, e.g. with PP |
| Recycling | Hardly possible, mostly energy recovery | Engravings and pure parts can be re-melted |
| Colorability | mostly black, color available | almost unlimited |
| Material price per kg (2026) | 6 – 15 EUR/kg | 5 – 13 EUR/kg |
| Tool costs | medium (press tools) to high (injection molding tools) | high (injection molding tools) |
Table 1: Comparison of standard EPDM with TPE (TPE-V / TPE-S)
6. What is the main difference in the processing of TPE and EPDM?
The main difference in the processing of TPE and EPDM lies in the type of crosslinking: EPDM is crosslinked in a heated tool through a minute-long chemical reaction (vulcanization); TPE is simply melted and solidified upon cooling. A manufacturing cycle therefore takes several minutes for EPDM, only a few seconds for TPE.
How is EPDM processed?
First, a mixture of EPDM rubber, fillers such as carbon black, softeners and crosslinking chemicals is produced and optionally prepared for use as feed strips or roll sheets for processing. The rubber mixture is then placed in a heated mold using the press, transfer or injection molding process and vulcanized there for several minutes at approximately 160 to 200 °C depending on the wall thickness. Subsequently, the rubber moldings are removed from the mold. Due to the high pressure, material is pressed between the mold’s parting planes, which requires a subsequent deburring process through mechanical punching or cutting or an automated freeze deburring process.
How is TPE processed?
TPE raw material is supplied as granules in bags, melted in a injection cylinder or extruder and injected hot into a cool, tempered tool. The component solidifies within seconds upon cooling. No post-treatment is usually necessary, and burrs can be directly recycled as grinding material into the process.
7. What is the difference between TPE and conventional rubber when it comes to recycling?
The most important difference in recycling: TPE is fusible and therefore recyclable in material terms; vulcanized rubber, however, is not. Scratches and broken parts from TPE can be recycled back into the production as grinding material and processed again. Composite components, impurities, and a certain loss in properties during repeated processing limit the process.
Vulcanized rubber can no longer be melted due to its chemical crosslinking. Common methods of disposal are:
- Grinding into granules or flour, e.g. for fall protection panels, cow stall mats, sports floors or as filler in new mixes
- Fragmentation of the interconnected rubber by devulkanization. The process is technically established, but is only used industrially to a limited extent.
- Pyrolysis and energy recovery, e.g. in cement plants
8. Current price development of TPE compared to EPDM
Both materials are based on petrochemical raw materials. EPDM and most TPE types are based on ethylene and propylene; TPE-S, on the other hand, is based on styrene and butadiene. Accordingly, prices react strongly to oil prices, energy and logistics costs.
Prices for TPE and EPDM have increased on both sides in 2026. TPE produced in Germany costs approximately 5 to 13 EUR/kg in 2026, while EPDM blends cost approximately 6 to 15 EUR/kg. The wide range is due to the type, hardness, formulation, required approvals, and the volume of sales.
However, the raw material price is only one factor when calculating a component. In addition to the lower average cost per kilo, TPE benefits from shorter cycle times and reusable molds. This is offset by higher costs for injection molding tools. Therefore, a potential cost advantage for TPE depends on the specific component and is determined by the quantity, tool costs, cycle time, and waste.